The John Moyle Field Day 2018: Another successful field day.

Another Field Day success. This time my main goal was to rake up a few contacts during the John Moyle Field Day, operating from Mt Coot-tha in Brisbane with my FT-817 and Buddistick antenna. But this time, instead of squeezing the most out of 5W, I hooked up my new HF Packer miniHFPA2 Edition linear amp that puts out a massive 30W. And the beauty of this is that I would only need my 7 A/H gel cell to power it.

My set up for the day, from left: Yaesu FT-817, HF Packer miniHFPA2 amp, LDG-Z100Plus tuner. Behind: Yaesu FT-70D, Sotabeams powwerpole distribution box on top of 7 A/H gel cell.

I mounted my Buddistick antenna to a BBQ grill behind the operating bench that looked as though it had seen better days. Fortunately the G-clamp just fitted.

The Buddistick did a good job and was easy to erect. I chose it over a dipole as there was no ready method to secure my squid pole close to the operating bench.

Well, at the start of my 40 minute activation, my battery showed 12.69 V and at the end, 12.60 V. And that was after continuous SSB work on 40m. So 9 QSOs later, I was content to pack things up and head for home.

Advertisements

Beating the downturn with the miniHFPA2

Everyone’s been complaining lately about poor propagation when it comes to amateur radio. But I think I have found the answer to my situation, especially considering I run an essentially low power operation.
I ordered a miniHFPA2, a linear amplifier that is made for portable operation out in the field.
This little beauty is the 5th generation HF Packer amplifier that comes pre-assembled, tested and calibrated. All I had to do was to hook it up to my Yaesu FT-817, then feed the output through an SWR/Power meter and Antenna Tuning Unit to my long wire antenna.

All set up and ready to test on air.

I happened to notice, on checking SOTA Spotter, that VK2IO Gerard and VK2/G4OBK Phil would be activating three summits, VK2/IL-001, 002 and 005 on Thursday 8 February 2018.. This would present me with an excellent opportunity to try out the new amplifier.

I tuned up on 40m and responded to their calls. Gerard mentioned that he was receiving me well and gave me a signal report of 569. This was excellent news, given the marginal conditions. I worked all three summits as they were activated and couldn’t have been more pleased. You see, normally my 5W output wouldn’t have been up to it in current conditions.

So what is this little gem of an amp all about?

According to Virgil Stamps, who makes the amps, the aim of his project is to give your signal a boost so you can start making memorable contacts under marginal conditions. It certainly has lived up to that! The amp gives a clean, more powerful output signal from a QRP transceiver with a good balance between output power, physical size and weight. And what’s sure to excite any SOTA or WWFF operator, it can be powered by any battery such as a 7.2 AH gel cell or 4.2 AH LiFePo4 battery. The amplifier provides a full output of around 30-35W with as little as 9V DC, making it very tolerant for outdoor battery operation.

What makes this amp a little different is the heat sink that is secured to the top of the enclosure. It isn’t the more common type that features rows of serious fins; it is a flat metal plate of around 1mm in thickness. And it does the job it is intended to do very well indeed. It lends itself to outdoor use as it can easily be accommodated in any backpack, but care does need to be taken so as not to damage the toggle switches on the front panel.

I particularly like the slim heat sink that is secured to the top of the enclosure.

The amp comes complete with two low pass filter modules (60/40m and 30/20m) but mine came complete with additional ones for 160m, 80/75m, 17/15m, and 12/10m as well. These modules are inserted into place by unscrewing the left and/or right hand side panels of the enclosure. They slip in effortlessly, thanks to cleverly designed guide posts on the LPF boards. I think when I proceed on my next SOTA activation, I will decide beforehand what bands I will be operating on as I think unscrewing side panels in a hostile environment such as on a summit could be a little tricky. Virgil did send along a sealed package containing spare enclosure screws, heat sink compound, two spare MOSFETS and some other items. Great service and attention to detail.

At the time of ordering you need to specify what level of input power you will be using. This could range from 1 to 5W; I chose 5W. Output power is an easy 30W. Spurious products are -40dB or better at 35W, with harmonic content at -45dB or better at 35W.

If you’d like to read up on the specifications, visit the web site http://hfprojects.com